Resin 3D Printers - Questions and Discussion
Moderator: Moderators
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
Whoah.
No.
If you want stl files of actual 40k models, we don't allow that here - not even discussion of it. IP laws and all that.
Now, if you want files for PROXY models, and models that look close... that's fine.
But we take IP protection very seriously on BTown. We'd treat the discussion of "where to I get stl files of GW models" exactly the same as we would "Where can I buy recast models?"
That said, I like Cults3D and Thingiverse for files. Also, Google...
If you want a Space marine proxy, do a google images search for "40k Space Marine.stl," and peruse the images. If you find an STL you like, follow the link and go directly to the page. It's often easier to find the file that way easier than going directly to a site.
Also, you could look at "40k Space Marine patreon," and find an artist who makes them.
Good luck on your quest.
Eric
No.
If you want stl files of actual 40k models, we don't allow that here - not even discussion of it. IP laws and all that.
Now, if you want files for PROXY models, and models that look close... that's fine.
But we take IP protection very seriously on BTown. We'd treat the discussion of "where to I get stl files of GW models" exactly the same as we would "Where can I buy recast models?"
That said, I like Cults3D and Thingiverse for files. Also, Google...
If you want a Space marine proxy, do a google images search for "40k Space Marine.stl," and peruse the images. If you find an STL you like, follow the link and go directly to the page. It's often easier to find the file that way easier than going directly to a site.
Also, you could look at "40k Space Marine patreon," and find an artist who makes them.
Good luck on your quest.
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
FAIL.MagickalMemories wrote: ↑Mon Jan 03, 2022 2:43 amTonight, I start my most ambitions project to date...
Thor's hammer, Mjolnir, by Wicked (who I've begun supporting on Patreon).
It'll be over 40 hours of PRINTING, and over a bottle of resin. And that's only because it's been hollowed!
Eric
Started with one head of the hammer. Supports on a corner didn't print right, and that side of the head came out wonky and messed up. : (
There's about 11 hours and $5 in resin down the drain.
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Re: Resin 3D Printers - Questions and Discussion
Okay, sorry about the breach of etiquette. I have found cult3d and thingiverse, also a site called 'yeggi' although it seems to just be a site of links and not actual stl's. The issue I am having with thingiverse is I am looking for bits, not entire models. Just the bits I am missing for the models I do own.
Are there any resources available to learn how to make your own STL's? I would like to make copies of the bits I do own for some of the older sculpts that are not supported anymore.
Are there any resources available to learn how to make your own STL's? I would like to make copies of the bits I do own for some of the older sculpts that are not supported anymore.
- YoungWolf777 ( 1150 )
- Millenium Trader
- Posts: 1034
- Joined: Fri Sep 08, 2006 3:08 pm
- Location: 84074
Re: Resin 3D Printers - Questions and Discussion
https://www.yeggi.com is a good place to start. It's a search engine specifically for STL files.
The biggest sites are https://cults3d.com/ and https://www.myminifactory.com/. There's also https://gumroad.com/, but I find it a bit tedious to navigate.
The biggest sites are https://cults3d.com/ and https://www.myminifactory.com/. There's also https://gumroad.com/, but I find it a bit tedious to navigate.
- YoungWolf777 ( 1150 )
- Millenium Trader
- Posts: 1034
- Joined: Fri Sep 08, 2006 3:08 pm
- Location: 84074
Re: Resin 3D Printers - Questions and Discussion
If you want to learn 3D sculpting, there's a great Blender tutorial series on YouTube.
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
Learning to make your own isn't as simple as "I have one and want to import it into this software with a scanner" or something.Bradgar wrote: ↑Tue Jan 04, 2022 5:30 pmOkay, sorry about the breach of etiquette. I have found cult3d and thingiverse, also a site called 'yeggi' although it seems to just be a site of links and not actual stl's. The issue I am having with thingiverse is I am looking for bits, not entire models. Just the bits I am missing for the models I do own.
Are there any resources available to learn how to make your own STL's? I would like to make copies of the bits I do own for some of the older sculpts that are not supported anymore.
You've got to know how to 3D design things and start from a blank canvas.
If you've got the long months and years to learn how, you'd be fine to learn that way. Probably start with YouTube and watch some videos, then start from there.
Another option some people use is to make molds of their existing bits. Either silicone, or even "push molds." Again, YouTube is a huge resource on how to do those.
Alternatively, you could try searching those sites for the specific bit you're looking for.
You could also post here, in our Bits Only forum and see if anyone has any available.
So, what are you specifically looking for?
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
So, I decided to abandon not only Mjolnir, but any and all large projects for now.MagickalMemories wrote: ↑Tue Jan 04, 2022 1:27 amFAIL.MagickalMemories wrote: ↑Mon Jan 03, 2022 2:43 amTonight, I start my most ambitions project to date...
Thor's hammer, Mjolnir, by Wicked (who I've begun supporting on Patreon).
It'll be over 40 hours of PRINTING, and over a bottle of resin. And that's only because it's been hollowed!
Eric
Started with one head of the hammer. Supports on a corner didn't print right, and that side of the head came out wonky and messed up. : (
There's about 11 hours and $5 in resin down the drain.
Eric
My print plate is convex. I knew this already, but it hadn't caused any major issues. So, I kept on printing. I DID open a ticket with AnyCubic, and they ARE sending a replacement... but Lord knows when THAT will arrive, and I don't want to sit around twiddling my thumbs.
So, I'll stick to smallish things. I think part of the reason for the supports failure might've been that convex plate.
Off I go to fiddle around!
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
- YoungWolf777 ( 1150 )
- Millenium Trader
- Posts: 1034
- Joined: Fri Sep 08, 2006 3:08 pm
- Location: 84074
Re: Resin 3D Printers - Questions and Discussion
That sucks Eric. You could try sanding it down if you're getting a replacement.
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
Oh, I will be! : )
I want the 2nd, in case I mess this one up... but there's no reason not to TRY to save this one. Right?
I was also thinking about finding a local metal worker/machine shop and asking them to do it. They'll be able to do a better job with their machines than I would by hand!
Eric
I want the 2nd, in case I mess this one up... but there's no reason not to TRY to save this one. Right?
I was also thinking about finding a local metal worker/machine shop and asking them to do it. They'll be able to do a better job with their machines than I would by hand!
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
- YoungWolf777 ( 1150 )
- Millenium Trader
- Posts: 1034
- Joined: Fri Sep 08, 2006 3:08 pm
- Location: 84074
Re: Resin 3D Printers - Questions and Discussion
True. Should be easy for them to plane it down level and smooth.
Re: Resin 3D Printers - Questions and Discussion
Before inserting my foot into my mouth, are we allowed to talk about STLs for non GW files? Say for items they don't have models of?
Say for instance a mycetic spore STL?
Say for instance a mycetic spore STL?
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
I got my build plate in from AnyCubic.YoungWolf777 wrote: ↑Thu Jan 06, 2022 9:24 pmTrue. Should be easy for them to plane it down level and smooth.
Sadly, it was ONLY a build plate. I'll have to remove the bracket from my old one and use it. : (
I'll have to see what I can do to get a replacement bracket or have one fashioned somewhere.
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
Yes.
Aaaaaaand no.
So, for example, you are MORE THAN allowed to look for "counts as" models.
"Hey. Does anyone have any good recommendations for who makes the best non-GW Space Marine proxies?"
You're NOT allowed to specifically look for things that violate copyright.
"Does anyone have an STL of the ForgeWorld Tyranid Harridan?"
So, if you want proxy models, and it's clear that you're not trying to use "coded" language to skate past our rules, you're ABSOLUTELY fine.
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Re: Resin 3D Printers - Questions and Discussion
Okay, thanks for the guidance, this is weird but I have just gotten access to a printer so it is good to learn the etiquette at the beginning of my journey.
-
- Lord Logorrheic!
- Posts: 16741
- Joined: Thu Sep 04, 2003 11:38 pm
- Location: St. Louis, MO - USA
Re: Resin 3D Printers - Questions and Discussion
Frankly, it's the beginning of the journey (on Bartertown, at least) for all of us. BT's never really delved into the area of 3D prints or trading 3D related stuff. So, aside from the obvious stuff about copyright infringement, it's all new around here.
Eric
Lower rating? You ship first.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.
Give me a sense of humor Lord. Give me the grace to see a joke.
To get some humor out of life and pass it on to other folk.
I think what this situation needs is some imagination.
"...I'm a nerd, and I'm here tonight to stand up for the rights of other nerds.” – Gilbert Lowell
Want my help with a BTR or backout? All messages sent/posted should be in CHRONOLOGICAL order. Otherwise, I just won't read it.